35W DC 5.5-30V to 0.5-30V LCD Digital Display Buck-Boost Voltmeter Ammeter

Description

Store category
Sign Up Now !
You may also like
35W DC 5.5-30V to 0.5-30V LCD Digital Display Buck-Boost Voltmeter Ammeter
Product Description
Buck-boost module (constant voltage constant current LCD version)
1. Product highlights:
1.1 LCD input and output voltage, output current output power;
1.2. Input anti-reverse protection, reverse connection will not burn;
1.3. Can be step-up and step-down, the output voltage 0.5-30V arbitrary regulation, limiting the current 0-4A arbitrary regulation;
1.4 output anti-intrusion, the battery charge without additional anti-reflux diodes;
1.5. Button control output ON / OFF status, and you can set the power-on default is ON or OFF;
1.6. Ascending and descending chip used as the main controller, external 60V 75A MOS tube as a switch, double 60V 5A SS56 Schottky rectification, 60V voltage value, superior to the market immature XL6009 / LM2577 program (a lot Device pressure value is not enough, MOS tube and Schottky diode pressure value must be greater than the input plus input voltage value);
1.7. Output ripple small, LC filter;
1.8. With heat sink, send module support isolation column.
2. Product parameters:
Input voltage: 5.5-30V (input voltage 5V, you can normally achieve buck-boost, but the voltage and current meter values ​​are not accurate; less than 4.7V, undervoltage protection)
Output voltage: 0.5-30V
Output current: long-term stable work in 3A, strengthen the heat can reach 4A
Output power: 35W natural cooling, heat dissipation to enhance 50W
Voltage display resolution: 0.05V
Current display resolution: 0.005A
Conversion efficiency: about 88%
Soft-start: Yes (very powerful with load startup, startup may fail)
Input reverse protection: Yes
Output anti-intrusion: Yes
Short circuit protection: yes
Working frequency: 180KHZ
Size: L * W * H 66 * 48 * 21mm
Mounting hole: 4mm in diameter
Weight: 46g
3. Function Description:
3.1. Module has IN / OUT, ON / OFF two buttons: IN / OUT button to switch the input voltage and output voltage display, long press to switch the output current output power display; ON / OFF button control output ON or OFF, long press Set power on default output status is ON or OFF.
3.2.CC is the current setting potentiometer, clockwise rotation, can increase the set current, when the load current reaches the set current, enter the constant current state, CC constant current indicator (red) lights up; the right CV is the voltage setting Potentiometer, clockwise rotation, can increase the output voltage. ON indicator is the output status indicator, when the output voltage is on, otherwise off.
4. How to use:
4.1. Used as an ordinary buck-boost module with over-current protection capability
(1) Adjust the CV constant voltage potentiometer so that the output voltage reaches the voltage you want.
(2) Measure the output short-circuit current with 10A current meter (connect the two test leads directly to the output end), and adjust the CC constant current potentiometer to make the output current reach the preset over-current protection value. (For example, if the current value displayed by the multimeter is 2A, the maximum current will only reach 2A when you use the module. When the current reaches 2A, the red constant voltage and constant current LED is on, otherwise the LED is off)
Caution: When using in this state, there will be a voltage drop of 0 ~ 0.2V due to the current sampling resistor at the output. At the same time, the input and output leads will have a certain linear voltage drop This is a normal phenomenon!
4.2. Used as a battery charger
Without constant current function of the module can not be used to charge the battery, due to the power of the battery and the charger pressure drop is large, resulting in charging current is too large, causing damage to the battery, so the beginning of the battery to use constant Flow charging, when the charge to a certain extent automatically switch back to constant voltage charging.
(1) Determine the float voltage and charging current for which you need the rechargeable battery (if the lithium battery parameter is 3.7V / 2200mAh then the float voltage is 4.2V and the maximum charging current is 1C, ie 2200mA)
(2) Under no-load condition, the multimeter measures the output voltage and adjusts the constant voltage potentiometer so that the output voltage reaches the float voltage. (If the 3.7V lithium battery is charged, adjust the output voltage to 4.2V)
(3) Measure the output short-circuit current with 10A current meter (directly connect the two test leads to the output terminal), and adjust the constant current potentiometer so that the output current reaches the predetermined charge current value;
(4) Connect the battery, charging.
(Steps 1, 2 and 3 are as follows: input termination power supply, the output is not connected to the battery load)
4.3. Used as LED constant current driver module
(1) Make sure you need to drive the LED operating current and the maximum operating voltage;
(2) Under no-load conditions, the multimeter measures the output voltage and adjusts the constant voltage potentiometer so that the output voltage reaches the maximum operating voltage of the LED.
(3) with a multimeter 10A current measurement output short-circuit current, while adjusting the constant current potentiometer so that the output current reaches the predetermined LED operating current;
(4) connected to the LED, test machine.
(Steps 1, 2, and 3 are as follows: Input the power and output the no-load LED.)
Note: This module is more than 3A, 35W use, please strengthen the heat! ! !
5. Note:
5.1. Module input IN- Prohibit short circuit with output OUT-, otherwise constant current function will be invalid.
5.2. Please make sure that the power of the power supply is greater than the power required by the output load!
5.3. If the module is to be fully loaded with output, the input voltage should be over 8V. When the input voltage is 5V, the output power is about 15W, and the voltage ammeter fails. Module current value 4A, the premise subject to the maximum output power, such as the output 17V, the current should not exceed 2A.
5.4. Module with output short-circuit protection, short-circuit protection module automatically shut down the output, the module can be restored on the power, if your power supply without output current limiting protection, it is recommended that the module input front-end fuse in series to increase the safety factor.
5.5. The module has input under-voltage protection function, the default is about 4.7V. Below this value, the output will be disconnected automatically and the module can be powered on again (note the voltage at the module port. When the input current is relatively large Do not ignore the partial pressure on the input wire).
Pls buy with confidence
Shipping
Payment
About us
customer service
Pls buy with confidence
We are spending more than  6 years in eBay business, we promise, we are an Honest and Hard-working seller, we do love our Job, we already try our best to provide best services.
Hope you enjoy your purchase in our store
If any questions and ideas, just feel free to tell us ,we are here for you or will be back to you within 24 hours.
Our reputation for excellent customer service has been built over 5 years of trading by providing great value and support to all of our customers. With tens of thousands of products shipped,we understand the things that matter to you, the buyer.
Shipping
We ship to Paypal registered address only!
Items will be shipped within 24 hours after payment received.
For Items that shipped from China is send by Airmail, it normally take 15-35 days for delivery
For Items that shipped from UK warehouse is send by Royal Mail
, it normally take 2-5 days for delivery, and
no tax to The European Union!!!
If you do not receive your item after 35 days. please contact us immediately for further assistance. We will be responsible for any damages or losses incurred in the shipping process.
Import duties, value added taxes and any other charges are NOT included in the item price or shipping costs. As an eligible importer,you are responsible for any reasonable tax or any other importation fees.
Payment
W
e accept
paypal
only !
Payment must be received in 5 business days .
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
About us
Specialized in electronic components and moudels.
Real store, Goods in stock.
Competive price. Good quality
We have more than 8 years experience in international business.have a wealth of experience in shipment. and we work with reliableshipment company, can get good price from DHL in Hongkong.
customer service
1. We take care of all requirements from every single valued customer, like you. Therefore, we do our best to control the quality of each item before sending.
2. In very rare case, if the product is found faulty, please contact us for return or refund.
3. In addition, we offer 30 days unconditional Refund Warranty and 1 Year Manufacturer Warranty.
4. We must be informed if you do not like the device within 7 days upon receiving the item and we will give you a returned merchandise authorization number (RMA). Without (RMA), the buyer will be responsible for any loss of return.
5. All returns must include all original items undamaged, in re-saleable condition, all original packaging including manuals, warranty forms, etc.
6. As we are selling all items on eBay from factory at lowest price, we are unable to refund you shipping and handling costs. Buyer is responsible for shipping costs incurred shipping products back.
Buck-boost module (constant voltage constant current LCD version) 1. Product highlights: 1.1 LCD input and output voltage, output current output power; 1.2. Input anti-reverse protection, reverse connection will not burn; 1.3. Can be step-up and step-down, the output voltage 0.5-30V arbitrary regulation, limiting the current 0-4A arbitrary regulation; 1.4 output anti-intrusion, the battery charge without additional anti-reflux diodes; 1.5. Button control output ON / OFF status, and you can set the power-on default is ON or OFF; 1.6. Ascending and descending chip used as the main controller, external 60V 75A MOS tube as a switch, double 60V 5A SS56 Schottky rectification, 60V voltage value, superior to the market immature XL6009 / LM2577 program (a lot Device pressure value is not enough, M
On Dec-14-17 at 03:11:23 PST, seller added the following information: